Search results

so my 91 940 has the following brand new A/C pump new dryer new orifice new o rights all through the system condenser has been flushed. new oil then it was all converted to r134 and charged. the system kicks on and the pump works fine--small line gets way to hot to touch and the condenser gets...

hey guys got a 91 940 t with a new engine and a brand new pcv system and i noticed tonight when i cranked the boost up to 18 lbs it popped the dipstick out and spewed oil all over :grrr: what have you guys done to make it stop doing that ? would putting a breather on the valve cover remedy this ?

my engine (1993 b230ft with porting and an ipd turbo cam and an adjustable cam gear) is all done and running great but i want to make sure its running at its best..the reason I'm curious is because it has kinda low vacuum at idle..around 12-13 inches and only about 4 cruising down the road. i...

bought a rebuilt and balanced t3 on the forum last month and just got to putting it on my new engine. has good oil flow and drain, and good coolant flow. turbo was primed well before stating it and then the boost was set to 7 psi and drove to town a few times..about 20 miles. when i got got home...

so my 91 940 t seems to have a vacuum leak in the dash. the heater will only blow air to the windshield. i can hear the air rushing through the controls on the dash or feet settings but not on the defrost or dash/feet settings. anywhere in particular i should look for leaks. I already replaced...

so guys i want your opinions on what kind of power i might be pushing with my setup. (at the crank) b230ft squirter block extensive porting on the head 90+ exhaust with extensive porting t3 with a .60 trim compressor housing volvo exhaust/wastegate full size npr inter-cooler new flow matched...

my wideband setup has a "narrowband output" wire that you can wire up to the oxygen sensor signal to your ecu so you only have to run 1 o2 sensor. my question is..does the factory ecu care if you have the heater part of the o2 sensor connected ? i know some ecu check to see if the heater hooked...

so my new engine is all built and I'm installing it tomorrow night...and I just realized my new turbo doesn't have a recirculation valve built into it like the factory one. can i run a BOV? cause theres no way I'm gonna buy another turbo. I'm pretty much assuming i cant go without anything?

this weekend I'm replacing my A/C compressor,o-rings,orifice, accumulator, and cleaning the entire system out. i have the adapters to r-134a already but i need to know how much oil and refrigerant i will need? car is a 91 940 turbo sedan.

my 940 sedan is fine unless i have several people in it and i try to accelerate hard...when i do it sounds like something is clunking against the underside of the body. almost like the drive shaft is hitting the body. it didn't change when i lowered it or when i put all new shock and struts on...

i have 205-55-16s on the 940 sedan right now with my ipd lowering springs and have to clearance issues but i could stand a wider tire. my g80 only seems to work 10% of the time so anything wider i can fit would be cool. is there any room to go bigger ?

im using Imgur.com to upload pics with bbcode and everything put up here is enormous...how the heck do you make the pictures smaller ? for some reason i can upload pictures to the site.

just realized there was even a place for a thread like this so here goes. picked this thing up a year ago from a couple for 400 bucks. it had sat under a tree in there back yard for 3 years with a bad overdrive solenoid and a leaky head gasket. brought it home and spend 2 hours scrubbing the...

i have the voxx wheels from ipd and i would love to put OEM volvo center caps on them. does anybody know what size center caps they take..ipd sell caps but there like 12 bucks a piece and if i can get Volvo ones to work ill get them on ebay. thanks

does anybody know what couplers you need to install a full size NPR intercooler in a 91 940. nobody around here sell elbows or anything and i have no clue what to order. I also need to bypass the resistor pack for the injectors and need to know how to do it. from what i understand you just...

just tried to put the oil pan on my new b230ft with a brand new Elring oil pan gasket and ran into 2 weird things. the gasket pops together like a puzzle...like literally has puzzle piece ends on it, no way thats what volvo used from the factory ??? :wtf: secondly the holes don't line...

so what are the best upgrades for lh2.4 turbo cars. my 940 is getting a new engine and i would like to give it some better ignition but i have been told never to run aftermarket coils cause they wont work well. Are there any bigger coils that will work well ? i already have Kingsborne wires and...

my 91 940 turbo sedan has the abs with the giant single piston calipers in front. i have Akebono pads all around and slotted and dimpled rotors but i was wondering if there calipers from any other Volvo that are dual piston or that have more clamping force. i know my 87 760 turbo had dual piston...

getting ready to put a new engine in my 2.4 940 it has chips--big turbo-- exhaust--porting--npr intercooler --etc etc etc going for 300 hp and i need to know exactly what injectors to run...preferably something reasonably price so maybe i can buy them new. and where to get the plumbing bits for...

I have alot of power draw in my 940 (stereo,high draw e -codes,etc) ans I'm having problems with the blue ground strap that goes to the intake getting really hot to the point if getting discolored. I have already upgraded to the 100 amp alternator. i was wondering, could a person take off the...