Search results

Customers left Komifornee on me. Looking for a decent shop for upkeep on their P2 Xc90 Thanks!

https://eastcoastgearsupply.com/i-1566317-dana-30-spider-gears.html https://www.skandix.de/en/spare-parts/drive-train/wheel-drive/differential/planetary-wheel-differential-pinion-side-gear-m27-kit/1044166/

There are no marks, what position is the slot supposed to be in, with engine @ TDC? And once this is correct, how do you confirm the CAS itself is not 180? out, it seems sealed? My guess is it don't matter. I have no interest in actually learning anything about how this works yet, I am simply...

Customer has fled the State, and settled here. '05 xc90 V8 Thank you!

Stock in all respects except need to be like 1/2" longer. Thanks!

Customer with minty '93 850 leaving me and this area for good. Need honest shop to refer her to. Thanks!

I'm pretty sure the answer is no, but thankfully my PRV memory banks have been mostly eradicated. Thanks

When the bronze shift handle bushing in the trans wears, to the point of the shift handle being quite sloppy, does the transmission have any other ill effects? Such as jumping out of gear, or any other drivability issues, other than the obvious annoyance of mop & bucket shift "pattern"? Thanks!

Just curious.. Is it the shape, the grain, both, neither? I'm mostly inquiring about the upper portion. Thanks!

Been daily-ing the ES after 10+ years of ownership @ 100 miles per year. These past weeks/months I've blown about 6 tanks through her, and am actually starting to appreciate and enjoy the thing. Does desperately need a (seat back mounted?) center armrest though! The shifter is a bit too...

Has anyone found the real deal, #3 Phillips direct replacement (McMaster Carr #?) or have the dimensions of an original, so I can figure it out for everyone? Thanks

Anyone been here? I did "search" first.

What did Volvo use to cobble this setup? Is it as simple as "our" (us spec) '86-'93 core support, fenders, '83-'85 bumper, '81-'93 E-codes, and regular recessed cowl hood and grill? Or is it a special unique-to-this-arrangement core support and grill? Thanks

Hi, Bought the Webber conversion kit from IPD. It comes with a new intake manifold, but to my surprise :roll: the Stromburger mani is one giant chunk-o-chit with the exhaust manifold. So, I ASSume I will need to find an exhaust manifold from a different stock setup, but which one? Earlier, or...

BESIDES E-Fan. It has lost all of it's love juice. Flex fan? What have others done? This is the shroud-less yellow plastic fan/thermo-visco-clutch setup. I'd love to find a NOS or regular new replacement clutch.

Relay 2/80 (R2) which is integrated into the CEM (4/56) is not activating. From what I gather GSM (Gear Selector Module) 3/156 sends a LIN signal to TCM (4/28) TCM tells the CEM that the GSM is in reverse gear, CEM commands 2/80 "on" and reverse lights light. Now my dilemma is how to confirm...

What is the purpose of the magnet in the shifter "blind" on P1 chassis cars? There is a small magnet attached to the "blind" (the thing that hides the shifter slot and moves with the handle). Basically I'm wondering if it could be for reverse light function? P1= '04.5 S40, V50, '05+ C70, C30.

So, 2 speed 850 cooling fan LH 2.4 (939 Fuel Computer) Wife's 244 b230ft. Everything is wired up correctly, I can ground pins 10 or 11 on fuel computer (the pins I just added to the connector for the fan relay) and the fan whirls over perfectly, both speeds. The issue is that, the ECU is not...

I have a single layer Wolf, non custom fit cover that kinda fits my 262c. But he'll have to be outside this winter, (rain, snow, pine needles, little-to-no sunlight) and I need something nicer. I am pondering a fleaBay $120.00, five layer "custom fit" one. Any first hand suggestions...

I bought this: http://yhst-26451710505916.stores.yahoo.net/b2t5trad.html And the nose tube (where the T/O bearing rides) it comes with, has an ID which is smaller than the OD of the sealing surface of the B.W. T5. Hence the mainshaft bearing retainer is not allowed to make contact with the case...