Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
Hello Guest, welcome to the initial stages of our new platform! You can find some additional information about where we are in the process of migrating the board and setting up our new software here
... But I have replaced the sensor twice. The last sensor measured 2.23k ohms across the terminals at room temperature. How can I test the wiring? I?m assuming test for continuity from connector to the ecu, but I don?t know what pins on the ecu, and to be honest I?ve never looked for the ecu...
My vacuum controlled Vents were functioning at a level that they would only blow from the dash vents whenever I didn’t have the throttle more than 1/8th of the way down. I of course hate having to choose between AC and accelerating, And I also hate the idea of removing the entire dash from my...
1994 NA 940
Recently replaced head gasket. Fan runs constantly while engine is running, CEL is on. Replaced both temp sensors on the side of the head, both are currently connected. What else could it be?
1994 940
I have a head gasket swap that went from a weekend to many weeks due to other stuff. Now I can?t figure out a couple things, so I am here to ask for help.
#1. There is a large black hose I can?t figure out. I thought it attached to a ?black can? on the side of the block, but that...
1994 945
I have been having trouble with random stalling while driving. I'll just be heading down the road and the car will just completely die. sometimes it won't start for a minute, sometimes it won't start for an hour.
After a little bit of googling, I was encouraged to check the fuel pump...
So the vents on my 940 only work right under maximum vacuum. I need to fix them properly, but I was hoping someone had a temporary, non-destructive way to jam the flapper dash vents open. Any ideas?
Hey everyone!
1994 940 n/a
Tomorrow I?m going to have to find some injectors at the boneyard. Does anyone know what cars other than the 740/940 use the same injectors?
My 1994 945 NA has been intermittently sputtering recently, seemingly regardless of being at idle, no throttle, part throttle, or full throttle. The only exception is never at high RPM, at least not that I can tell. when it is running right its 100% fine. There seems to be no rhyme or reason as...
1994 945 n/a
My battery was dead one morning, so I charged it. I drove around the next day without trouble, but the following morning it was dead again. I replaced the battery with a brand new one, and there was a fair amount of arcing when I connected the battery just for running the clock, but...
A little while back someone posted on here that they had installed the front seats from some Korean car into their 7xx/9xx. I lost track of the thread, and have no idea exactly which car they were talking about as the donor. Does anyone know?
1994 940 here -
I'm planning to re-do all the suspension this fall. I think I want to use 240 strut cartridges in my 940, with shorter than stock springs, and a spacer in the bottom of the 940's strut housing. I have a few questions I couldn't find answers to.
1. Do the 240 cartridges fit in...
1994 940 -
At the risk of sounding like a total moron, what are some good jacking points on my car, keeping in mind my desire to use jack stands? I've only had it a few months, and I haven't needed to get under it yet.
I have a few different things on the web about installing a new water pump, but there are a few details I am still unclear on.
1. Do I try to put the bolts in before or after pushing the pump up?
2. Speaking of the bolts, I should use sealant on the threads of the ones that go into the block...
Like the title says. It's pretty far gone at this point. Instead of dropping ~$90 on a new one, are there any practical alternatives? For example, is the handle from a 740 a drop in replacement? How about a generic alternative that will actually fit the square shaft? I could probably move the OD...
Hey everyone!
1994 940, n/a.
I have started replacing the water pump, and I have run into a few head scratchers.
#1. When I removed the upper timing belt cover, the rear cover started crumbling to pieces. Is this normal?
#2. I don't absolutely need to put the timing cover back on, do I...
As I understand it, the two common options are IPD and some sort of factory brace. Which is better? What cars can I find the factory brace on? Are there any other options?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.