-
Hello Guest, welcome to the initial stages of our new platform!
You can find some additional information about where we are in the process of migrating the board and setting up our new software hereThank you for being a part of our community!
Cam and I built one of these David Vizard budget flow benches
- Thread starter shoestring
- Start date
redblockpowered
bad username length
- Joined
- May 5, 2015
- Location
- Swampscott, MA
Next step is to print a sweet velocity stack for intake ports but I have broken my Solidworks install somehow and need to rebuild it.
Parameters here: look it's a hyperlink I forgot you could do this
I thought it looked like a dank hash pipe.
It took forever to cure, like four or five days. I ended up keeping it in my bedroom with the heat on blast to help it out.
Parameters here: look it's a hyperlink I forgot you could do this
I thought it looked like a dank hash pipe.
It took forever to cure, like four or five days. I ended up keeping it in my bedroom with the heat on blast to help it out.
What silicone did you use?
I’ve use Smooth-on 2-part for ports, and for molding at work. Very good products.
www.smooth-on.com
I’ve use Smooth-on 2-part for ports, and for molding at work. Very good products.
Mold Making & Casting Materials | Rubbers, Plastics, Foams & More!
Smooth-On manufactures industry-leading two-component materials such as silicone, urethane rubber, urethane plastic, urethane foam, epoxy resin, epoxy coatings and adhesives.
www.smooth-on.com
redblockpowered
bad username length
- Joined
- May 5, 2015
- Location
- Swampscott, MA
This was Alumilite, via dubious Amazon seller. Second thing probably key.
- Joined
- May 3, 2010
- Location
- LFK
is that body safe silicone?
We've reached a new technological frontier. This is a ported intake port. We're out of stock ones. Note the almost comical lack of features.
redblockpowered
bad username length
- Joined
- May 5, 2015
- Location
- Swampscott, MA
Just needs the flange. Now available in luxurious teak.
redblockpowered
bad username length
- Joined
- May 5, 2015
- Location
- Swampscott, MA
redblockpowered
bad username length
- Joined
- May 5, 2015
- Location
- Swampscott, MA
I fixed it to account for shrinkage
redblockpowered
bad username length
- Joined
- May 5, 2015
- Location
- Swampscott, MA
Fit check:
I deburred it at the junction between snorkus and intake port due to start of print woes but beyond that the fit is dead on.
Also, there's another one.
I have flow numbers for the original clay radius, plastic snorkus, and no snorkus in the notes but haven't converted them to CFM yet.
Also, there's another one.
I have flow numbers for the original clay radius, plastic snorkus, and no snorkus in the notes but haven't converted them to CFM yet.
shoestring
Well-known member
- Joined
- Jun 20, 2009
- Location
- Swampscott, 01907
Replace above photo with one sans Roundel, bitte.
redblockpowered
bad username length
- Joined
- May 5, 2015
- Location
- Swampscott, MA
Sorry should have censored that.
redblockpowered
bad username length
- Joined
- May 5, 2015
- Location
- Swampscott, MA
Here's where I have been putting the flow numbers
I made this a lot more human-readable before posting but it's still a little rough. Early numbers may be a little dubious. Any questions, just ask.
I made this a lot more human-readable before posting but it's still a little rough. Early numbers may be a little dubious. Any questions, just ask.