hardware/ threads faq

[BGoins12]

Anyone know how much I need to torque the bolts down for the rear main seal carrier plate?

 

[vvpete]

Anyone know how much I need to torque the bolts down for the rear main seal carrier plate?

IIRC they are 7 lb/ft torque.

 

[BGoins12]

I figured it was something low, mainly because of the size of the bolts. I just tightened them and snugged them a bit, so probably around 10-12 ft/lbs. Plus I used threadlocker so they should be good for another 160k or so.

 

[smokeyfan1000]

1978-1991 240 steering column SHAFT where steering wheel retaining nut threads on is M18-1.5 thread/count.

I'm told 140s - 1977 240s have same threads/count also

 

[Mueller]

Didn't see the starter bolts in this FAQ. I had to cut off the heads and then lost the rest during my slow rebuild job on a 1990 240DL.

bump for starter mounting hardware....even a pic could help right now

 

[HonestJhon]

Flexplate hardware


Flexplate to crank and flex plate to torque converter...?

anyone? in the final stages of this build and wanted to replace the old hardware (if i even have it anymore...) involved in bolting these things on.

 

[HonestJhon]

checked, dont have any spare crank bolts (none in the new motor)

if anyone has a motor laying around they could check , that would be greatly appreciated. crank bolts and torque converter bolts.

 

[HonestJhon]

nothing? i havent been over to the motor to work on it for a week....but still need the info!

i'd like to be able to order something from jegs or summit....
maybe RSI stocks something?

anyone?

 

[HonestJhon]

bolt that fits for the crank is m10x1.5 length, im guessing is something in the 40-50mm range.


my last resort is to order them from the dealer. i just have a feeling these are going to be in the 5-6 dollars each range.

 

[542]

A link to anything you need to know re AN fittings
http://www.precisionenginetech.com/tech-explained/2009/05/20/an-hose-and-an-hardware-part-1/

5 pages worth of reading, bottom right of article takes you to next page (not totally obvious). Lots of photos and explanations. I find Summit, Jegs etc.. frustrating when looking for fittings as its all not in one spot and always going back and forth to compare

 

[740tankDriver]

what is the thread size on the main fuel pump check valve? not the compression-seal side the thread for the check valve to the main pump.

 

[cleanflametrap]

(For Mueller)

 

[MistrThou]

From impvolvo:
Lower chassis brace for 7/900
10mm x 1.5 pitch x 25mm need 3 bolts and one 10mmx1.5 pitch nut

 

[J.B.]

Does anyone know off hand the size & pitch of the studs/nuts on the exhaust manifold flange-to-header pipe on an NA B230? I saw the manifold studs are listed here but not the next juncture on the exhaust. Possibly even the part #'s for said three studs and copper lock washers.

 

[cleanflametrap]

Does anyone know off hand the size & pitch of the studs/nuts on the exhaust manifold flange-to-header pipe on an NA B230? I saw the manifold studs are listed here but not the next juncture on the exhaust. Possibly even the part #'s for said three studs and copper lock washers.

Surprised this wasn't in the thread already, and it was asked before at #81 but not yet answered.

M10 (1.5) -- nothing exotic. Don't know length, but can look up p/n: 977581

 

[smokeyfan1000]

Surprised this wasn't in the thread already, and it was asked before at #81 but not yet answered.

M10 (1.5) -- nothing exotic. Don't know length, but can look up p/n: 977581

This might help a little for part numbers.

Buying them from ww.tascaparts.com is what I did.

http://forums.turbobricks.com/showt...ight=exhaust+manifold+studs+nuts+part+numbers

 

[Harry Tuttle]

From the thread referenced above:

I think we need a "Volvo Part Number List" stickied on TB somewhere

+1 on that

 

[$EEKING 945 TURBO WAGON]

Favorite quality thread pitch gauge sources? LARGE PRINT

Who sells a thread pitch gauge that has old man eyes sized readable stamped print; and useable sizes without wasting space with impractical sizes- and maybe NOT CHEESY QUALITY?

Metric/ SAE/ both?

 

[122power]

M47 drail and fill plug 18mm x 1.5.

 

[Sir Psycho]

What's the length of the M8x1.25 exhaust studs?